Difference between revisions of "Doc:Following a Spline/es"

From Synfig Studio :: Documentation
Jump to: navigation, search
(Tutorial)
Line 3: Line 3:
 
== Introduction ==
 
== Introduction ==
  
Si estás usando la versión 0.61.08 o anterior, por favor, dirígete al tutorial "siguiendo una Bline (método antiguo)", since this version is about the {{l|Source code|in-development version}}, which you can {{l|Build instructions|build from source}}.
+
Si estás usando la versión 0.61.08 o anterior, por favor, dirígete al tutorial "siguiendo una Bline (método antiguo)", ya que esta versión es acerca de la versión en desarrollo, que se puede construir desde el código fuente.
  
This is only a rough draft.  The content should be OK, but it needs tidying up and could really benefit from some screen shots.  If you follow the tutorial, please consider taking some shots as you do so and uploading them here...
+
Esto es sólo un borrador.  The content should be OK, but it needs tidying up and could really benefit from some screen shots.   
  
 
Este tutorial muestra cómo hacer que un objeto siga el camino de una línea arbitraria, rotando para seguir encarando la dirección del camino.
 
Este tutorial muestra cómo hacer que un objeto siga el camino de una línea arbitraria, rotando para seguir encarando la dirección del camino.
Line 63: Line 63:
 
Bien, ahora tenemos seleccionadas dos capas y un pato de cada una de ellas
 
Bien, ahora tenemos seleccionadas dos capas y un pato de cada una de ellas
  
now additionally select the curved bline layer (it should be the last layer in the Layer panel's list) by holding Control and clicking on it
+
ahora además, seleccionar la capa de la curva BLine (que debe ser la última capa en la lista del panel de capas) pulsando control + clic sobre ella
  
right-click on the dotted line that indicates the position of the curved bline - not on any duck, but on the dotted link between ducks
+
haga clic derecho en la línea de puntos que indica la posición de la curva BLine  -pero no en cualquier pato, sino en el enlace de puntos entre patos
  
from the context menu that pops up, select "Link to BLine"
+
Seleccionar "conectar a Bline" en el menú contextual
  
 
the encapsulated arrow should move so that its green position duck is on the bline, and it should rotate so that the arrow points along the bline at that point
 
the encapsulated arrow should move so that its green position duck is on the bline, and it should rotate so that the arrow points along the bline at that point

Revision as of 10:51, 27 April 2010

Languages Language: 

English • čeština • Deutsch • español • français • русский

Warning!

This page contains outdated information.

The release of Synfig Studio 0.64.0 introduced new terminology and this translated page needs to be updated according to original English text.

You can help updating this page - see instructions here. Thank you!

warning end


Esta página debería estar escrita en Español. Por favor ayúdanos a traducirla!

Introduction

Si estás usando la versión 0.61.08 o anterior, por favor, dirígete al tutorial "siguiendo una Bline (método antiguo)", ya que esta versión es acerca de la versión en desarrollo, que se puede construir desde el código fuente.

Esto es sólo un borrador. The content should be OK, but it needs tidying up and could really benefit from some screen shots.

Este tutorial muestra cómo hacer que un objeto siga el camino de una línea arbitraria, rotando para seguir encarando la dirección del camino.

Summary

Esto es lo que vamos a hacer:

Tutorial

Este es un breve tutorial que nos da un ejemplo de cómo hacerlo:

Crea la Animación

File > New

Crea las Capas

seleciona la herramienta "Línea Bézier" (BLine) Bline tool.png

permite sólo la casilla Contorno

dibuja una curva (una Bline) sobre la que quieras que se mueva la flecha.

click en el icono "Herramienta línea Bézier" en la parte inferior izquierda de la "Paleta de Herramientas" para crear la Bline.

Todavía en esta herramienta,habilita "crear contorno" y "crear región" en la paleta de opciones

dibuja una flecha o lo que quieras, apuntando a la derecha

cambia a la herramienta "Normal"

selecciona el contorno, pulsa control-a para seleccionar todos los patos menos el pato verde de posición

arrastra los patos de modo que la flecha quede centrada en el pato verde de posición

añade una capa de rotación sobre las capas contorno y región

encapsula las capas rotación, contorno y región

Ahora tienes 2 capas: una que es un trayecto curvo y la capa encapsulada (Lienzo en línea) conteniendo la flecha y la capa de rotación

Moviendo y Rotando la flecha

Selecciona la capa encapsulada haciendo click en el panel de Capas

Selecciona el pato verde de posición haciendo click sobre él en la ventana Canvas

luego selecciona la capa Rotación pulsando control+click sobre ella en el panel de Capas

ahora selecciona el pato azul "cantidad de rotación" pulsando control+click en la ventana Canvas

Bien, ahora tenemos seleccionadas dos capas y un pato de cada una de ellas

ahora además, seleccionar la capa de la curva BLine (que debe ser la última capa en la lista del panel de capas) pulsando control + clic sobre ella

haga clic derecho en la línea de puntos que indica la posición de la curva BLine -pero no en cualquier pato, sino en el enlace de puntos entre patos

Seleccionar "conectar a Bline" en el menú contextual

the encapsulated arrow should move so that its green position duck is on the bline, and it should rotate so that the arrow points along the bline at that point

select just the encapsulation layer, and drag its green duck around. you'll see that the duck is constrained now to lie on the bline, and that dragging it also affects the rotation of the arrow as expected

we can now animate the arrow. turn on "animate edit mode" by clicking the icon in the bottom right of the canvas window.

at time 0f, drag the encapsulation layer's green position duck to one end of the bline

at time 5s, drag the same position duck to the other end of the bline

Try File > Preview or View > Play to watch the animation.

Results

This is the animation I ended up with: Arrow-follows-bline.sifz‎

Commentary on the Feature

Also, the arrow takes the same time to move along each segment of the bline. So if there's a long straight part then a bendy complex part, the arrow will move much faster along the straight parts (since there will be less vertices in that part).

It would be good to have the option of having the arrow move at constant speed along the length of the curve.


Languages Language: 

English • čeština • Deutsch • español • français • русский