Time Loop Layer

Revision as of 11:22, 19 March 2016

Language:

English

About Time Loop Layers

The Time Loop layer can be used to repeat an animation over and over. It loops a section of the layers below and within the same canvas over and over.

See also the Time Loop ValueNode conversion, which can be used to loop the value of a single parameter, rather than an entire layer or group of layers.

Parameters of Time Loop Layers

These parameters, to prevent undesired modification, by default are statics.

Once they are no more statics, like any other parameters in Synfig they can be animated, so that they change over time. This can be confusing, so make sure you aren't in Animate Edit Mode when working with the Time Loop layer, unless you know what you're doing!

The parameters of the time loop layers are:

Name	Value	Type
Z Depth	0.000000	real
Link Time	0f	time
Local Time	0f	time
Duration	1s	time
Only For Positive Duration		bool
Symmetrical		bool

Link Time (time)

Start time of cycled material/child layers.

Local Time (time)

Start time of loop. (this is currently (since 120323 at least) broken and has no effect on time loops, see http://synfig.org/forums/viewtopic.php?f=12&t=3526#p14986 for a discussion)

Duration (time)

Number of seconds or frames that are looped in the child layer.

Only For Positive Duration (bool)

• If checked and "Duration" is zero or negative, then the time loop layer is effectively disabled, and acts as if it wasn't there.
• If not checked and the Duration is zero, the Time Loop layer freezes the animation of the children layers at the value of "Link Time".

Symmetrical (bool)

If not checked, and the current time is less than "Local Time", then "Duration" is taken off the resulting time. This is to provide compatibility with version 0.1 of the time loop layer.

How to loop

The Time Loop layer repeatedly loops through the "Duration" seconds of its child layers, from "Link Time" to "Link Time" + "Duration". "Local Time" is used to line up the offset of the time looping. When the Time Loop layer is asked to set its time to "Local Time", it sets the time in its child layers to be "Link Time", ie. the start of the loop.

Breaking loop

1. In the layer's parameters of the time loop, you need to remove the 'green guy' from Duration Parameter. Just right-click on him and set "Allow animation". 2. On the timeline navigate to a place where you want to break the animation. And enter the Animation Mode. 3. In the time loop parameters, set 'Duration' to "EOT" (End-of-Time). 4. Now you have three waypoints. One before the current, we left it as it is. One is current, we convert it to the "constant" (right-click on it -> Both -> Constant). And one after current, this one have to be removed (right-click on it -> Remove). 5. Now test it. Pay attention, that loop will always break at the very first frame of you animation, so you need to break it in the right place.

Detailed explanation

'Green guy' is a guard that says "You shall not pass!" to the animation. So when you attempt to change such parameter in animation mode it just changes the usual way. It's done to prevent unnecessary parameters to be animated, e.g. 'Blend method'.

Setting 'Duration' to EOT. If you set it to 0f, then the whole animation will stop, because you try to play it from 0f (local time) to 0f (duration). And EOT means it'll continue to play your animation to the end of the time...

Removing waypoint after current one. If you skip this step, then at the next waypoint 'Duration' parameter will be restored to the value before current waypoint. It's a standard Synfig's behavior, but there's a magical button somewhere that can change it.

Converting current waypoint to the constant. Without it, 'Duration' will be smoothly interpolated from value you set to the EOT and the constant type will just set immediately at the waypoint. Interpolation can be a bit confusing sometimes, so you better read this: http://wiki.synfig.org/Waypoint

Visualized Example

For example, suppose:

• Link Time is 5s
• Duration is 3s
• Local Time' is 4s

And suppose that the Time Loop layer is applied over an existing animation. The "Link Time" and "Duration" specify that the section from 5s to 8s in the children layers will be looped. The "Local Time" specifies that this loop will be at the beginning at 4s. (And so also therefore at 1s, 7s, 10s, etc).

This is how the mapping actually works:

Specifying a huge number for the Duration parameter effectively turns the Time Loop layer into a Time Shift layer. The Link Time and Local Time parameters controls which time in the children lines up with which time in the Time Loop layer, giving the amount of the timeshift, with both positive and negative differences working as expected.

Contrived Example

Download and examine this example file: Time-loop-demo-0.2.sifz

It's a 10 second animation, and shows 2 circles. The top one moves linearly from the left to the right. Its position is marked by static text digits 0 through 10.

The other circle is an identical copy of the first one, with the same waypoints, but it's inside an Group layer. The parameters are:

• Link Time: 5s
• Duration: 1.5s
• Local Time: 2s
• Symmetrical: true

So as time=2s, the top circle is at position 2 (local time) and the bottom circle is at position 5 (link time):

The loop is 1.5s long, so the bottom circle is also at position 5 every 1.5 seconds before and after this point in time, for example at t=3.5s and at t=8s:

The following two images show the positions at t=0s and t=3s. The loop starts at t=2s, so it's also at the start at t=0.5s. So at t=0s it's half a second before finishing the previous loop. And at t=3s the same is true, but 2 loops later on:

There's a rendered copy of this example on YouTube, and it's also available for download: Time-loop-demo-0.2.avi‎.

Language:

English